How to use DMM Cam, warning, lifespan, inspection, care and maintenance with instructional pictures.
The 4CU 0 is technically retired but it's still sold online.The 4CU 0 is no longer produced by DMM. We're showing it as "available" on WeighMyRack because you can still find it at trustworthy online retailers.
This top quality lightweight, dual stemmed cam has proved to be very popular, and it is easy to see why. The 4CU is quick and easy to place; it also offers stable secure protection across a variety of crack features.
There are 11 different sizes in the range which fit a huge array of crack shapes and sizes, in fact anything from half an inch (13mm) to a meaty 4 inches (100mm). We have even put in two extra intermediate sizes, 1.25 and 1.75, which slot in between the most commonly used sizes of 1, 1.5 and 2; just what you need for dealing with that awkward crack width that runs between rattley finger jams, to ring locks and on to narrow hand size.
There are lots of interesting technical details which give 4CUs the edge on other double stemmed cams. Some of this might seem a bit techy, but it really will make a difference to how the cam performs at the crag. The free floating, peened axle for example reduces stress and helps to avoid a sheering torque at the point of impact.
The cam lobes work on the original 13.75° camming angle which gives the best balance between holding power and range. And the cam stops allow a (10kN) strength even when placed passively.
As with all of our cam designs, the 4CUs are fitted with double extendable dyneema slings. This means neat storage and quick and easy extension if you need it.
We’ve made the trigger bar free-floating so it can slide on the trigger wires. This reduces wear and tear on the wires and means you won’t have to worry about replacing them each season.
When you click a link below and then checkout online, no matter what you buy (climbing gear or not), we get a small commission that helps us keep this site up-to-date. Thanks!
|Weight (g / oz)|
Weight (g / oz)
In grams and ounces, the weight, as stated by the manufacturer/brand.
|75.0 g / 2.65 oz|
|Cam Head||4 lobes, single axle|
|Stem||Flexible double stem|
|Sling||25 cm Dyneema (double loop)|
|Camming Angle||14° |
|Active Strength|| 12 kN|
Single loop strength rating is 12kN and double loop strength rating is 14kN.
|Cam Range (mm / in)|
Cam Range (mm / in)
In millimeters and inches, the maximum dimensions of the cam lobes when shut tight and fully extended. Since the "usable" range is so debatable, all manufacturers now list the full dimensions to avoid confusion.
If a manufacturer lists the usable range, we'll include it here as well (this is now very rare).
| Total dimensions|
13 mm x 19 mm / 1 in x 1 in
So, to summarise, 4CUs are an excellent choice for someone looking for a versatile, lightweight and easy to use camming device. They have been my choice of cam for many years and while I have used most of the other brands on the market, I always reach for my trusty 4CUs when I rack up for a tricky route.
They do what it says on the tin. Not exciting exactly but then as much as I might get excited by cams in the shop, when I'm climbing I want them to quietly go about their business without fuss. They do exactly that and are solid and dependable. I could wish that the triggers were a little longer on the smaller sizes to give more reach into deep placements but that is a relatively minor complaint. I also found the double stem can be awkward in a tiny minority of constricted placements but it was very rare and wouldn't stop me choosing 4CUs. I checked all the cams in this review for use with gloves and mitts for winter climbing and the 4CU was slightly harder to use with my gloves on but, oddly, the only one I could reliably use wearing mitts. To cover a range from 19-100mm you would have 7 units weighing a total of 983g
Summary: The most noticeable thing about the DMM 3CUs and 4CUs are their bright colors, which makes picking the correct size from a crowded rack a breeze. Each unit's cam lobes, trigger bar, and thumb bar are anodized to match, and, yes, the doubled sling blends right in too. The trigger bar allows for a bit of independent cam manipulation -- rare on a U-stem unit. Another unique feature are the cam lobes (with integrated cam stops), which are wide when fully retracted and taper to a more standard width near the end of their range. When the cam is placed tightly, there is more cam surface against the rock for greater grip -- great for parallel cracks, but if the crack is flared or irregular the cams will sit awkwardly. Another drawback is the trigger bar's tendency to slide up the trigger wires toward the head. The extra step of pulling the trigger back into position is easy, but a burden on pumpy routes.
Pros: Extendable sling; trigger bar allows for some independent cam action; great color coding; cam stops; light.
Cons: Poor performance in flared or awkward placements; trigger bar slides down.
The UIAA equipment standard provides a baseline for equipment performance in a test lab under controlled conditions on new equipment. Although these test conditions are relevant to the conditions encountered climbing, conditions encountered at the crags and the condition of the equipment are equally important. This recommendation from the UIAA member federation The British Mountaineering Council (BMC) provides vital equipment information that is NOT explicitly addressed in the standard, particularly failure modes of the equipment and recommendations for the use, inspection, maintenance, and retirement of equipment.
A pictoral representation of the UIAA-125 and EN-12276 standards for frictional anchors (which includes SLCD's [cams] and Ballnuts).